@xB Most of the steps occur outside our software and are down to whatever tool or utility you use to launch your sim environment.
The command line switch above allows 3rd party utilities to load a previously saved profile without the user having to "mouse navigate" as you would normally do.
You can thus customise the wheelbase's behaviour to suit different sims/environments without having to manually select the profiles.
Where the command is entered would be dictated by the utility in use.

@aotto1977

Hi
yes the same, I have a sw20 v3, I advised two friends to turn to v4 Unfortunately they got tired of waiting with a month of delay and the lack of communication of not having an answer and apparently they did well because it went from pre-order to: no longer for sale... too bad it's good to devote yourself to development but if you develop so as not to sell it's a little missed your target... 🙄😬😉🙏🏽

@Sim-plicity-Dev
Hi,Hello,
sorry I completely forgot to comment. Indeed it is the QR on the steering wheel side that is starting to loosen up, in addition to that, the base of my aluminum profiled playseat was slightly unscrewed.. which makes with the power of the engine produced, it's a snap at each change of direction. Thank you again for taking the time to respond to me. And sorry for taking so long to get back to you. Wishing you a good day. Cordially.

"Center Wheel" in the simplicity software has always worked for me even if its just a few degrees out.

@xB

Just had a quick play with KartKraft & would say it's not a hands-off-the-wheel type of sim.

With this in mind, it should be possible to get a realistic/useable feel without overdamping the wheel.

Can you post a screenshot of your Input Bindings screen within KartKraft as well as your Settings, Advanced and Telemetry tabs from within the SW25 desktop app

@Sim-plicity-Dev Thanks for confirming.

Thanks,

After reseating the plugs all seems fine again.

@Sim-plicity-Dev
Thanks for your help

@JeanV78

See reply here

@frijsdijk

Your description suggests UCR is grabbing control of the FFB channel from iRacing (probably on startup).
You can get iRacing to wrest control back by disabling then re-enabling FFB within the Options>Force Feedback menu

Make sure you exit the Options screen between disabling and enabling.

@Sim-plicity-Dev said in USB PCI-e controller not working with SW20v3 base:

@frijsdijk

The wheelbase heavily exercises the USB bus and will forcibly eject itself if the bus it is connected to is not sufficiently stable.
As your description suggests all is fine using the motherboard ports, it would appear the PCI-E USB bus is currently below the stability threshold.

Replacing your USB cable with a new Shielded cable would be a first step in raise the bus stability over the threshold.

Thank you! I'll try some time (found other solutions)

@Sim-plicity-Dev said in Firmware v21.10.01:

We are currently aiming at end of March (dependent on the release of our new hardware platform)

@Sim-plicity-Dev, Thank you!

@Sim-plicity-Dev
I played again yesterday and it had the lack of FFB issue came back. I deleted the ACC profile, but all the settings were still there so I reassigned the wheel anyway and the problem was still there.

I then tried playing not in VR and it was ok and then went back to VR (hp reverb) and it was fine again, so I'm wondering if something is glitching with the VR software maybe?

@Sim-plicity-Dev , Thank you!

Hi,

though I'm quite late to the party, I might still help. 🙂
I got my SW8C+ running with DR2 using this guide: https://cdn.cloudflare.steamstatic.com/steam/apps/690790/manuals/DR2_Multi_Input_Device_Configuration.pdf

My device ID is 028A1CBE-0000-0000-0000-504944564944

@sim-plicity-dev , thank you for this detailed and explicit information!

@sim-plicity-dev

New cable (Ugreen 2m shielded USB2 A to B, for reference) seems to have done the trick, will leave it on for a while to see if there's any drops but so far so good.

86b77e52-2ebf-48f4-b40c-ba89c99dabfc-image.png

Will report back if any issues occur.

Cheers,

Dan

@txinas

Easiest way is to

open a new command window, drag the Presets Installer executable into the command window type " /p:rbr" after the path (without the quotes, make sure to include the space) Hit Enter

If you have any issues, post a screenshot of the command window

@storris

A USB Reset is the controller forcibly removing itself from the USB bus.
This only happens if the controller detects a connection to the PC but is unable to communicate.
If the USB cable is physically removed from either controller or PC, the controller detects this and disables USB monitoring till the cable is reconnected.

As no resets are logged, this implies the controller has detected the connection is gone and is on standby. This means we need to look outside the controller for the cause of the physical connection dropout.

This could be hardware (cable, connectors, USB controller), software (Windows drivers, settings etc) or firmware (motherboard BIOS).

The controller does exercise the USB bus quite heavily with a thousand 2-way transmissions per second. Any latent issues with the USB subsystem will thus manifest first in devices that are heavy users.

Searching for "amd usb issues vr" brings up a few reports similar to yours.
This one details the steps that worked in his instance